Skip to main content

Blog entry by Micah Bonython

Guide To Fix Door Hinge: The Intermediate Guide Towards Fix Door Hinge

Guide To Fix Door Hinge: The Intermediate Guide Towards Fix Door Hinge

Glass-Replacement-150x150.jpgHow to Fix a Loose Door Hinge

Window-Repairs.-150x150.jpgThe majority of homeowners can fix a loose hinge. But, if the holes for screws are smashed and can't hold screws, you might need to add wood glue and dowels before you can reinstall the hinge.

Remove any surface rust. This will aid in keeping the dowels in place and provide a solid base for them to rest on.

Take the Hinges off

Many standard door hinges are removable, which makes it easier to move the door from one side to the other or to remove the entire door off the frame if need be. Anyone with a bit of patience can remove the hinges, however, you must know what to do.

If the hinges have been painted, you'll need to remove the paint before you attempt to remove the pins. If you don't, the paint will be smashed off and scratch your door when you attempt to lift it. To break the paint seal put the hinges into an stainless steel pan and fill the pan with water until the double glazing hinges are completely submerged. The hinges should remain in the pan for approximately 30 minutes. The heat from the water should soften the paint and make it easier to take off the pins.

After the pins have been loose, remove the replacement double glazing hinges and the frame from the repair door hinge. You can use a screwdriver to get the job done, but it is recommended to employ a magnetic screwdriver to complete this task. This type of screwdriver was created to remove screws made of metal and make the task go much faster.

It is a good practice to spray some lubricant on the hinges before attempting to remove them. A simple lubricant can make the process to go more quickly and help you remove the pins and screws. This kind of lubricant is able to be found at most hardware stores and home improvement stores.

The number of hinges needed will also depend on the kind of door you have and the way it's installed. Heavier doors and solid-core doors will require more hinges while hollow-core doors with a lighter weight might only require two or three hinges.

It is also essential to know the various types of hinges to determine which ones work best in your situation. The hinges on the exterior are designed to support the weight of a door, but interior hinges need to be able to handle heavier loads.

Reattaching the Hinges

Sometimes, a hinge on a door will become looser over time and begin to hang crookedly or sag. This can be a major problem, but the fix is usually simple. In most cases it's a simple tightening of the screw will fix door hinge the problem. If the screw holes have been stripped out, it can be difficult to Fix Door Hinge. A wood dowel could be used to tighten the holes once more.

Begin by drilling the hole using a drill close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a tight fit, the dowel should be cut at the same length as the screw. Install the screw again and tighten it to the desired tightness. If the door still has the tendency to be bowed the door, then add a second dowel to the gap and repeat the process. Make sure to close the door slowly in order to check the perimeter clearances after each adjustment.

You can also use a wooden plug in place of the dowel. This will work similarly, but it may take a little longer to install. Simply whittle a piece of wood that is the appropriate size for a comfortable fit, then tap it into the hole. If you don't have a woodworking tool you could also use toothpicks or wooden matches.

Make use of a countersink in order to make the hole smaller for the head of screw after you have reinstalled it. This will stop the screw from rubbing against the edge of the doors as they are closed and opened. This will allow you to tighten the screw when you are reinstalling the hinge.

Once you've reinstalled your hinge, make sure to lubricate it using a dry lubricant to ensure that it doesn't get stuck in the future. Products such as PB Blaster or Liquid Wrench are excellent alternatives. You should apply a light coat and allow it to take about 15 minutes to fully penetrate the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace the hinges on your door, you are able to make a few minor repairs. Make sure the screws that hold the hinge plate in place to the door frame as well as the frame are tight. If they're loose, tighten them by using a drill or screwdriver. Be cautious not to tighten the screws to the point that they cause gaps at the trim joints or, even more damagingly cause threads to be stripped.

If you're experiencing issues because the hinge plates are separating from the jamb and door it is possible to reattach them by applying wood glue to the back of the plates, and then inserting wooden dowels or toothpicks into the holes. Dowels and toothpicks provide a solid base for the screws, and prevent the plates from shifting when you push them in. Let the glue dry before reattaching the hinge.

The screws may also be stripped or missing. This issue can be resolved by replacing the screws. Use a drill bit that is similar to the size of the screw hole to prevent drilling into the hinge or jamb.

After you've reattached your hinge close the door and check the gap between the frame and the door. It should be about the thickness of one nickel all around or less if there's a gap that was caused by a door that was not properly hung. This should not be a problem as long as the hinges are properly installed.

If the hinges are still loose, you could add an extra thick hinge between the surface of the hinge plate and the mounting surface. This will give the hinges more room. You could also try taking the hinge pin from the troublesome hinge and pounding it down with a hammer to make it tighter or using an entirely new hinge pin. You can also lubricate your hinges with mineral oil or jojoba to reduce friction and help keep them in position. Lubricating your hinges regularly can aid in keeping them from becoming stiff or squeaky and can also extend their life.

Cleaning the Hinges

A hinge's continuous movement causes friction, which attracts dust particles. These particles may get stuck and build up in the moving parts of door hinges if they are not cleaned and lubricated regularly. The hinge will get stiff and creaky and its appearance can rapidly change. Regular cleaning, lubrication and inspection will preserve the functionality and quality of hinges on a door.

Check the hinges to see how much rust has formed on their surface. If the corrosion has reached the point of damaging the surface of the hinge barrel or screw holes, you'll need to replace the hinges. If you're able to save the hinges, you can remove any loose rust by using steel wool and wire brush. Then apply a commercial rust remover or homemade solution like lemon juice to the hinge. Allow the rust-removing solution to remain on the hinges for a few minutes to penetrate and dissolve the remaining rust.

If you do not want to spend money and time replacing hinges, tightening the screws can make the casement windows hinges functional again. If you've stripped the screws' holes, however, it may be necessary to attach a wooden dowel or shim to the hinge. Dowels made of wood come in round rods of various lengths and sizes. They can be purchased on the internet, at stores selling woodworking supplies and home improvement stores.

You can also make a shim from a piece made of plastic or metal depending on the type hinge you have. To make a dowel cut a wooden dowel to the desired length. You can then dip a dowel into carpenter's adhesive and then insert it into the hole. The glue will secure the dowel in the desired position.

Before cleaning the hinges put down a paper cloth or towel to shield your flooring from spills. After you have protected the area clean the hinges with a soft sponge or cloth coated with mild cleaner to get rid of dirt and grime. You can also remove tarnish, dirt, and grime. A small brush or toothbrush can be used to access difficult-to-reach spots in crevices or tight spots.

  • Share

Reviews